![]() Here are some photos of the VERSION ONE Interceptor in use on a 08 Caliber SRT-4.Nope no new pistons, stock motor so far for the hahn kit. Installation is accomplished by simply plugging the supplied connector into the OBD2 port below the steering wheel. This is accomplished through a simple menu selection. Last but not least, the Interceptor will measure 0-60 times, as well as 1/8 and 1/4 mile time and speeds. The gauge has bi-directional controls allowing for manaul control of the low and high speed fans. ![]() These signal can then be read and recorded along side the other parameters obtained on the vehicle's bus. ![]() These inputs are handy for pressure signals such as those from MAP and oil pressure sensors, analog outputs from Air/Fuel ratio kits, etc. A linear conversion can be entered so that an analog signal connected to the gauge can be read in appropriate units. The two analog inputs can be configured through menu choices. has been inadvertently left disconnected, or something was just not put back together properly. Those that have modified their vehicle will find this very handy when a sensor, vacuum line, etc. The Interceptor's scan rate can also be adjusted through a menu function.ĭTC's (Diagnostic Trouble Codes) can be accessed and cleared via menu options.This essential feature will help the gauge to pay for itself the first time the check engine light comes on. Positive images are easier to read in bright sunlight, negative at night. Not only can this be visually appealing but beneficial in changing lighting conditions. Using this feature, for example, the gauge with a black backround and blue characters (negative image) becomes a blue backround with black characters (positive image). Once you try it you'll find you can't live without it!Īnother menu option offers the ability to swap the foreground and backround colors of the display. Due to the gauges extremely fast update rate, this light is very accurate and easy to set. High intensity LEDs can be used as shift lights or warning lights to indicate when a selected parameter exceeds an entered threshold. This way you can monitor several items without taking any other actions. The gauge displays 2 parameters at a time, but can be programmed to cycle through up to 8 parameters during a user determined period of time. Returning to the menu screen, you can choose to replay the stored data on the Interceptor display. Approximately 60 seconds of data will be stored. Once selected, the Interceptor will return to normal scan mode, but will start recording the displayed data automatically when the throttle exceeds 60%. One menu option allows you to enter a record mode. A 5' cable is included with appropriate OBD2 connector.Ī function menu is available by pushing both buttons simultaneously. The Interceptor gauge is 52mm (2 1/16") in diameter and will fit in all standard gauge pods of this size. Ability to record engine parameters for 60 seconds and review parameters.Ability to check AND ERASE ENGINE CODES.Manifold Pressure (vacuum/boost) displayed in PSI. ![]() Intake Air Temperature (post Intercooler).Heres a listing of some of the many different engine parameters that can be viewed with this gauge. Light output of this gauge is RED, to match the instrument cluster lighting Now you can choose any combination of white face/black face, and silver bezel, black bezel!įurthermore, you can now get a special SS specific gauge face in your choice of silver, white, or black for only $15 more! View the SS gauge faces below, and select which gauge face you want in the pull down menu before adding the gauge to your cart. Having interchangeable faces and bezels makes it easy to change the look of your gauge within seconds. This version of scangauge, is feature wise exactly the same as the previous gauge, except now it has a series of interchangeable faces and bezel. Because the OBD2 port communicates lots of different parameters of your engine, you can view tons of information! Furthermore, it will not interfere with the OBD2 ports operation, because it simply plugs in, and is not hardwired, and no wires are cut, chopped or soldered for the gauge to work! The OBD2 port is a diagnostic port that is used for dealerships, service stations, and even emissions testing facilities to connect a computer to your car to see how your cars running, problems with your car, etc. The Scangauge, is a very special type of instrument gauge that connects within seconds to your cars OBD2 port, located right below your dashboard. Introducing a new version of Aeroforce Inteceptor Scangauge. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |